AMPED Wireless Setup – Guide

In this article, you will find the guide to setup amped wireless range extender and extender on your own. The guide easy to use and the steps are simple to perform. Most people are acquainted with the setup process of a new range extender or extender. But here Amped allows you to set up a brand new range extender and extender by using this guide. Make sure you should follow this guide only if you are using the Amped Wireless networking equipment like routers and extenders. Correct configuration setup for new range extender amped setup is very crucial because if the channel and frequency of the router are not set correctly then it could result in slow internet speed and frequent disconnection in internet connection.

Amped Wireless Setup Instructions

Before getting started with the Amped Wireless Setup Instructions I would like to inform you that in case, you want to skip this step process and want some from amped to do it for you then you could contact the team at a number given below and they will assist you with setup for free. Now Let’s get started right now with Amped Wireless Setup Guide, Make sure you do not skip any of the given steps below.

Amped Wireless Range Extender Placement 

Here is the tip for you; before moving forward towards the amped wireless setup you must determine the location where you have to place the Amped Wireless extender because correct placement is very important for the router performance. Your internet speed and Wi-Fi range all depend so much on the right placement of the range extender is that you could lose it all if done it properly. You have to find the optimum location wireless extender and your wireless dead zone. If you are using any range extender then you must not place amped wireless range extender far away from it.

amped wireless extender setup wizard
amped wireless extender setup wizard

Attach and Connect

Once the placement location of the amped wireless router is determined now you have to attach the wireless antennas to the range extender that came along in the box. You could easily find the antennas in the packaging box of an amped wireless extender.

amped wireless setup wizard page
amped wireless setup wizard page

Now you have to connect your amped wireless extender with the AC power supply and switch it on. Once the amped extender shows up the light then you have to use a laptop, tablet or smartphone to connect with the range extender network to begin the setup initially.

Amped Wireless Setup Dashboard

Now you have to login into the amped wireless setup dashboard to perform the setup steps. To do so you have to open a web browser and go to the default gateway address http://setup.ampedwireless.com. And then press enter. This address will lead you to the amped range extender dashboard. If you find that the webpage is asking for a login username and password then you have put the default username and password given at the backside of the range extender. If you face any issues in login then you must follow the troubleshooting steps given below to make a successful login.

amped router setup
amped router setup
  • Disconnect your laptop from all other Wi-Fi networks.
  • Attach Ethernet cable between your laptop and range extender
  • Go to the same web address if you are not able to open it then try another browser.

Scan Networks using Amped Extender

Once you are able to log into the amped wireless range extender dashboard then you would see the current status of the range extender shown in the dashboard. Now you have to click on the Scan button to find the networks to extend. Once the scan is finished you see the list of found networks near your range extender. If you are not able to find your internet router home Wi-Fi network then you have to restart the amped range extender and scan again. Make sure that your found network must have more than 70% percent of signal strength to get improved internet Wi-Fi Speed. Select your home internet network and click on the next option to continue with the setup.

amped wireless setup ac2600
amped wireless setup ac2600

Connect Amped Extender with Router

Proceeding further now we have to connect the amped range extender with the router and if you have set any security username and password for your router then you have put the same while connecting amped wireless extender with the router. Now, once you are connected with the router then the amped extender will ask you to set a username and password for the extender itself. You can clone the same for a new range extender setup but I do not recommend that. I suggest you set a new username and password which does not match with the router Wi-Fi.

amped range extender setup
amped range extender setup

I hope you are now able to setup amped wireless ranger extender. If you are still facing some kind of issue then I suggest you to contact the team and they will you to resolve it for you. More articles are coming soon on this topic.

Leave a Reply